Hi3516CV300 Sony IMX323 2MP H.265 IP Camera module board
Feature:
Support HKvision protocol (iVMS4200 and NVR)
Ultra low power consumption
Support WIFI(default MT7601)/TF(128GB) via USB
Support 1 channel Audio input & Audio output
2MP Hi3516CV300 + IMX323 specifications (H.265) | |
Module information | Default username: admin Password: admin IP: 192.168.1.88 Mobile phone monitoring software: Danale |
Sensor part | |
chipset | Hi3516CV300 + IMX323 [Ultra Low Power] |
sensor | 1 / 2.9 "Sony IMX323 CMOS sensor |
Minimum illumination | Color 0.01Lux@F1.2 |
Signal to noise ratio | > = 50db (AGC OFF) |
Wide dynamic range | > 80db |
Main chip encoding section | |
Encoding type | H.264 encoding MJPEG encoding |
Bit rate size | Adjustable 32kbps-8Mbps, fixed stream and variable stream (CBR & VBR) |
Video frame rate | PAL: 1-25fps NTSC: 1-30fps adjustable |
Main video stream | 1920 * 1080, 1280 * 960, 1280 * 720 |
Secondary video stream | 704 * 576, 640 * 480,640 * 352, 320 * 240 |
Interface Protocol | Standard ONVIF2.4 and GB28181 protocols |
Network protocol | TCP / IP, UDP, RTP, RTSP, RTCP, HTTP, DNS, DDNS, DHCP, FTP, NTP, PPPOE, SMTP, UPNP |
Network Interface | RJ45 10M / 100M adaptive Ethernet port |
USB interface | Support extended 4G or wifi, TF card maximum support 64G |
audio port | 1 channel audio MIC linear input 1 channel audio output |
Storage type | Manual, automatic (cycle, timing, alarm switch, motion detection) |
Alarm data transmission | Support FTP, Email, browser, management software output |
Number of visits | Support 8 users at the same time online browsing |
Other functions | |
working environment | -10 ~ +60 ° C, Humidity: 10% to 90% |
power input | DC 12V / 2A or POE power supply (expandable) |
Power consumption | < = 3W |
JP4 Power interface | |
1 | DC12V |
2 | CVBS GND |
3 | CVBS Signal Output |
4 | GND |
J6 Network interface | |
1 | RJ45_1 (TX+) |
2 | RJ45_2 (TX-) |
3 | RJ45_3 (RX+) |
4 | RJ45_6 (RX-) |
5 | Network connection indicator (green) |
6 | Network status indicator (yellow) |
J1 IR-cut interface | |
1 | IR-CUT control signal 12V |
2 | IR-CUT control signal 12V |
J3 infrared light board interface | |
1 | Infrared light board 12V power supply output |
2 | GND |
3 | Infrared feedback signal input (threshold 0.8V-12V) |
4 | Infrared light enable control |
J2 function interface | |
1 | Audio input |
2 | Audio ground |
3 | Audio output |
4 | Reset |
5 | Ground |
6 | USB_DP |
7 | USB_DM |
8 | 5V power supply output |
9 | Alarm output |
10 | Alarm input |
No. | Pin Defination | Pitch | Preview |
JP4 Power interface | 1.25mm | ||
1 | DC12V | ||
2 | Video GND | ||
3 | CVBS Signal Out | ||
4 | GND | ||
J6 Network interface | 1.25mm | ||
1 | RJ45_1 (TX+) | ||
2 | RJ45_2 (TX-) | ||
3 | RJ45_3 (RX+) | ||
4 | RJ45_6 (RX-) | ||
5 | Network connector light(Green) | ||
6 | Network status light(Yellow) | ||
J1 IR-cut interface | 1.25mm | ||
1 | IR-CUT control signal 12V- | ||
2 | IR-CUT control signal 12V+ | ||
J3 LED Board interface | 1.25mm | ||
1 | LED board 12V power out | ||
2 | GND | ||
3 | LED feedback signal (0.8V-12V) | ||
4 | Infrared light enable control | ||
J2 Function interface | 1.25mm | ||
1 | Audio in | ||
2 | Audio GND | ||
3 | Audio out | ||
4 | Reset | ||
5 | GND | ||
6 | USB_DP | ||
7 | USB_DM | ||
8 | 5V power out | ||
9 | alarm out I/O(3.3V Level signal) | ||
10 | Alarm in |